Question 1

Thank you. Please send the signed sample approval or an email confirming the sample number, drawing revision and approved specifications, together with your PO. We will issue the PI and production schedule; production begins after deposit and written artwork approval are both complete.

Accepted Answer

Thank you. Please send the signed sample approval or an email confirming the sample number, drawing revision and approved specifications, together with your PO. We will issue the PI and production schedule; production begins after deposit and written artwork approval are both complete.

Question 2

We can only recommend that for an exact repeat of an already approved part. For a new custom design, skipping validation creates fit, color and tactile risks that cost far more than a sample run. The safer fast-track is to start material preparation in parallel while samples are under review, without irreversible production until approval.

Accepted Answer

We can only recommend that for an exact repeat of an already approved part. For a new custom design, skipping validation creates fit, color and tactile risks that cost far more than a sample run. The safer fast-track is to start material preparation in parallel while samples are under review, without irreversible production until approval.

Question 3

Understood. Please tell me which keys and, if available, the measured actuation force. We can tune the dome force, spacer thickness or emboss geometry. I recommend one revised comparison set before production rather than adjusting by description alone.

Accepted Answer

Understood. Please tell me which keys and, if available, the measured actuation force. We can tune the dome force, spacer thickness or emboss geometry. I recommend one revised comparison set before production rather than adjusting by description alone.

Question 4

Screen color is not a reliable production reference because displays and lighting vary. Please evaluate under agreed light conditions against a Pantone code or a physical master sample. If you send the approved master, we will use it as the signed color standard for mass production.

Accepted Answer

Screen color is not a reliable production reference because displays and lighting vary. Please evaluate under agreed light conditions against a Pantone code or a physical master sample. If you send the approved master, we will use it as the signed color standard for mass production.

Question 5

I suggest five checks: fit in the housing, visual/color approval, tactile consistency, electrical continuity/contact performance, and environmental exposure relevant to your application. Please record any measured values rather than only “pass/fail.” If you share your end-use conditions, we can prepare a one-page validation checklist.

Accepted Answer

I suggest five checks: fit in the housing, visual/color approval, tactile consistency, electrical continuity/contact performance, and environmental exposure relevant to your application. Please record any measured values rather than only “pass/fail.” If you share your end-use conditions, we can prepare a one-page validation checklist.

Question 6

Yes. We can build a small comparison set, for example 250 gf, 350 gf, and 450 gf gf, with each version labeled. Your team can test them in the actual housing and sign off the preferred force. Please confirm the key diameter and available cavity height first.

Accepted Answer

Yes. We can build a small comparison set, for example 250 gf, 350 gf, and 450 gf gf, with each version labeled. Your team can test them in the actual housing and sign off the preferred force. Please confirm the key diameter and available cavity height first.

Question 7

Yes. Functional samples use the same approved overlay, circuit ink, adhesive and assembly process planned for production. If any temporary prototype method is used — such as laser cutting instead of a steel die — we will state it clearly on the sample report. Mass production starts only after your written sample approval.

Accepted Answer

Yes. Functional samples use the same approved overlay, circuit ink, adhesive and assembly process planned for production. If any temporary prototype method is used — such as laser cutting instead of a steel die — we will state it clearly on the sample report. Mass production starts only after your written sample approval.

Question 8

Estimated sample lead time is standard working days after payment and written artwork approval, plus carrier transit time. If the connector or special material is not standard stock, I will confirm the material arrival date before we commit the schedule. When do you need samples in hand?

Accepted Answer

Estimated sample lead time is standard working days after payment and written artwork approval, plus carrier transit time. If the connector or special material is not standard stock, I will confirm the material arrival date before we commit the schedule. When do you need samples in hand?

Question 9

For your current design, the prototype package is USD standard for target volume pcs, excluding courier, valid 15 days. It includes engineering drawing, production-equivalent materials and electrical testing. Laser cutting avoids production tooling at this stage. Shall I issue the sample PI?

Accepted Answer

For your current design, the prototype package is USD standard for target volume pcs, excluding courier, valid 15 days. It includes engineering drawing, production-equivalent materials and electrical testing. Laser cutting avoids production tooling at this stage. Shall I issue the sample PI?

Question 10

We can send existing reference samples free for material and tactile evaluation; courier cost is on your account. Custom samples require engineering work and are charged at USD standard for target volume pcs, fully credited against the first production order. Which type do you need — a reference kit or your custom design?

Accepted Answer

We can send existing reference samples free for material and tactile evaluation; courier cost is on your account. Custom samples require engineering work and are charged at USD standard for target volume pcs, fully credited against the first production order. Which type do you need — a reference kit or your custom design?

Prototyping, Testing and Sample Approval

Are you looking for a reliable manufacturer？

Products

Solutions

Company

Resources